Toilet Installation
In addition to matching colors and styles with all of you bathroom or powder room, you will again want to consider the points. Here are five steps to the next toilet installation is very easy to make.
(1) roughening of the specification: This is the measurement of the wall to the nearest outlet. Usually they come in 10 “, 12″ and 14 “sizes. The standard is 12″ but the measure must be taken.
(2) Foot Print toilet: When dealing with a break above the existing floor, you may want to refer to specification sheets for the area that the bottom of the toilet will cover. For new construction or new flooring option is also a good idea to have a reference so that the floor fairly close to the ring on a toilet flange.
(Three) high Toilets: ADA toilets are not only sold to people who need them. New term “high comfort.” Taller people, parents and all other forms of moving in the direction of a higher toilet that you do not have far to go there until nu.
(4) longitudinal / front Round: Long, the “larger goals” for the younger family members. Some weakness is that some people do not like the looks and if the bathroom or even smaller average size, can come to a salient point on the road.
Before you begin: Comply with all pipes and building codes. Carefully inspect new toilets for the damage. If there are toilets that do not have a closed-off value in the bottom of the tank, install one before installing the new toilet.
Please note that the risk of personal injury or damage to the product. Handle with care. Vitreous china can break or chip like the nuts and bolts, or if the product is picked up.
Installation instructions
Step 1: Remove the old toilet
Turn the water supply. Flush the toilet and sponge the remaining water. Disconnect the water connections. Remove the old cap bolts, toilet, and T-bolts, and scrape the old wax seal from the closet flange.
Install new T-bolts. If the delayed installation of new toilets, while closing the hole closet flange with a rag.
Step 2: Install new bowl
Record the model number on the owner’s Guide. The bottom of the cup, firmly press the new seal around the outlet of the bowl. Remove the cloth, and (if used) from the closet flange.
Caution: risk of external leakage. Not lift or after placement of the stone bowl – if you have a watertight seal, use a new wax seal. Average and below the bowl on top of the closet flange and T-bolt. Apply full body weight on the edge of the bowl to seal up. Do not assemble metal washers and nuts at the T-bolts at this time.
Connect these basic bolt in a position “up” on each bolt-T. Place the washer and nut for each bolt-T.
Please note that the risk of damage to the product. When cutting the excess of the long T-bolts, on the surface of vitreous china to protect against exposure to the blade.
If the T-bolts extending more than ΒΌ “(6mm) of beans, cut the excess cap Snap. Bolts bolt base of each cap.
Step 3: Install Tank
With three bolt tank, pre-collected through the gasket hole, place the tank on the bowl with a focus on the gasket on the inlet of the bowl. Put washers and nuts to bolts of the tank. Tighten the three nuts so that the tank level. Make sure the nuts well enough to achieve a watertight seal.
Step 4: Connect the supply
Close the supply valve on the supply of toilet to keep. Open supply valve slowly and check for leaks. Put the toilet seat. Try flushing the toilet several times. Regularly check the leak for several days after installation.
Step 5: Adjustments
Adjust the tank water to the water line marked by pressing and sliding the C-clip on the stick float. To increase the water level, slide clips C-ups. To lower the water level, slide down the C-clips.
Installation instructions
Installing a toilet is a very simple job and you have very little product in addition to what’s in the box (s), but here are some things that need to be replaced, while in the area.
Wax Ring: Cheap and good idea to replace, even if you take off the toilet and back into the same flange. Note: horned rings easier to line up and help prevent leakage.
Toilet bolts: cheaper, but you do not need to change this unless you have a long cut. brass not corroded and difficult to manage. Note: Provide plastic models tried. Large plumbing review.
Supply line: If you work in the area, the supply line range from toilet to toilet and can be old and cracked. Change, and save the possibility of headaches down the road. Note: braided line works well. They are flexible and add to the room looking neat.
Take the dried plant. If the bowl and the tank is no longer connected, put the bowl in place. Make sure the footprint that the area affected by the floor covering and not to tremble. When installing a two-piece toilet, after you come down, set the tank on top to ensure that the correct permissions on the back of the bowl, and on all sides.
Note: Write down the numbers of tanks and basins below the tank lid for future reference.
If you are unsure of your progress and you think you have a number of leaks, water shut after filling the tank. If there are leaks, you have only one water tank on the floor instead of an unlimited supply. When installing two-piece toilet, you can connect the tank into the bowl before setting. When the two parts, was lighter and easier to move. However, connecting the tank get a lot easier when the tank is not to escape to the floor. Do not forget to tighten the tank bolts evenly.
Make sure the lid bolt anchors are before the nut on the bolt toilet. If the hat does not fit in the anchor, or if the bolts seem long, it cuts.
Finally, if you are unsure of your skill and think you have some leakage, water shut after filling tank. If there are leaks, you will just a water tank on the floor is not an unlimited supply.
